Menu

ASTM A593 PDF

0 Comments

we manufacture one of the widest ranges of ASTM A Fasteners. Exporter of a wide range of ASTM A Fasteners in India at Best Factory lized. or visit us at ASTM F Scope – This specification covers the chemical and mechanical requirements for stainless steel. This specification for ASTM F covers the requirements for stainless steel bolts , hex cap screws, and studs to in., inclusive, in nominal diameter in a.

Author: Mezil Netilar
Country: Cameroon
Language: English (Spanish)
Genre: Health and Food
Published (Last): 19 November 2012
Pages: 345
PDF File Size: 20.78 Mb
ePub File Size: 14.7 Mb
ISBN: 319-3-83505-312-5
Downloads: 53100
Price: Free* [*Free Regsitration Required]
Uploader: Kigrel

Option A tests should be made whenever feasible. SH – Machined from strain hardened stock or cold worked to develop the specific properties.

ASTM F – 17 Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs

AF – Headed and rolled from annealed stock and then reannealed AH – Solution annealed and age hardened after forming CW – Headed and rolled from annealed stock thus acquiring a degree of cold work. Special fasteners have full size heads shall be tested as specified for stud bolts and other bolts. A Where options are given, all the tests under an option shall be performed.

D Yield strength is the stress at which an offset of 0. This specification covers the requirements for stainless steel bolts, hex cap screws, and stud bolts in imperial size 0. D When approved by the purchaser, alloysSe, or XM1 may be furnished. F When approved by the purchaser, alloys or Se may be furnished. A Unless otherwise specified on the inquiry and order, the choice of an alloy from within a group shall be at the discretion of the fastener manufacturer B See section 4.

D Yield strength is the stress at which an offset of 0. B legend of conditions: Please find below chemical, mechanical, 5a93 condition, heat treatment, marking and other requirements on Stainless Steel Bolts. AF – Headed and rolled from annealed stock and then reannealed AH – Solution annealed and age hardened after forming.

  IEC 60909-3 PDF

CW – Headed and rolled from annealed stock thus acquiring a degree of cold work.

B Tests that are not mandatory C Special fasteners are those fasteners with special configurations including drilled heads, reduced body, etc. Condition AF – When Condition AF is specified, the austenitic alloys shall be annealed in accordance x593 Condition A after all cold working including heading and threading has been completed.

AF – Headed and rolled from annealed stock and then reannealed AH – Solution annealed and age hardened after forming CW – Headed and rolled from annealed stock thus acquiring a degree of cold work. C The yield and tensile strength values for full size products shall be computed by dividing the yield and maximum tensile load value by the stress area for the product size and thread sizes determined in accordance with Test Methods F C The yield and tensile strength values for full size products shall be computed by dividing the yield and maximum tensile load value by the stress area for the product size and thread sizes determined in accordance with Test Methods F D When approved by the purchaser, alloysSe, or XM1 may be furnished.

E When approved by the purchaser, alloy F may be furnished. F When approved by the purchaser, alloys or Se may be furnished.

A Tensile stress areas are computed q593 the following formula: A – Machined from annealed or solution annealed stock thus retaining the properties of the original material; or hot formed and solution annealed. Hex head, square head and hex socket cap screws. E When approved by the purchaser, alloy F may be furnished.

  KUROI JUKAI ENGLISH PDF

ASTM F Specification – Boltport Fasteners LLP

B Tests that are not mandatory C Special fasteners are those fasteners with special configurations including drilled heads, reduced body, etc. CW – Headed and rolled from annealed stock thus acquiring a degree of cold work. Option A tests should be made whenever feasible. A Where options are given, all the tests under an option shall be performed.

ASTM F593 Type 316L

AF – Headed and rolled from annealed stock and then reannealed AH – Solution annealed and age hardened after forming. A – Machined from annealed or solution annealed stock thus retaining the properties of the original material; or hot formed and solution annealed. A Unless otherwise specified on the inquiry and order, the choice of an alloy from within a group shall be at the discretion of the fastener manufacturer B See section 4.

Special fasteners have full size heads shall be tested as specified for stud bolts and other bolts. Hex head, square head and hex socket cap screws. SH – Machined from strain hardened stock or cold worked to develop the specific properties. A Minimum values except where shown as maximum or as a range.

Condition CW – When Condition CW is specified, the austenitic alloys shall be annealed in accordance with Condition A, generally by the raw material manufacturer and thenc old worked to develop the specified properties. ASTM F covers seven groups of stsinles steel alloys, including twelve austenitic, two ferritic, four martensitic and one precitipitain hardening.

A Minimum values except where shown as maximum or as a range. B legend of conditions: A Tensile stress areas are computed using the following formula: