Menu

ALTECH RADIATORS PDF

0 Comments

Discover ideas about Heating Radiators. Graham The Plumbers’ Merchants are a UK supplier of radiators and towel warmers. Heating RadiatorsTowel. offers 3 altech radiators products. Diffuser altech radiator valves radiator valve connectors heat radiator valve. US $ / Set. Sets (Min. This product is only available for the Swedish market. Altech Radiators are available in versions K11, K21, K22 and K33, all made of steel plate.

Author: Gokinos Vicage
Country: South Sudan
Language: English (Spanish)
Genre: Environment
Published (Last): 21 February 2005
Pages: 404
PDF File Size: 15.66 Mb
ePub File Size: 16.49 Mb
ISBN: 269-2-57463-168-4
Downloads: 91506
Price: Free* [*Free Regsitration Required]
Uploader: Bralkree

High efficiency pumps are here. Old style pumps were driven by asynchronous motors. Setting the pump to one single pump curve is the only option in systems with constant hydraulics. There are two important things to remember here. In fact, it will destroy it rather quickly. This is the most common hydronic heating system. Simply put, on a nice afternoon in March, with spring in the air, only some rooms on the Northern side of the house may have open thermostatic valves while the vast majority of the house is warm enough.

The system resistance will be very high and the required flow of water low. On a cold December morning however, you have the opposite: To serve such systems best, the industry has come up with a control scheme called proportional pressure control.

It starts with the assumption that about half of your pressure loss in the altec will be in the distribution pipe while the other half is lost in the radiators. Consequently, the pump is controlled such that it will respond to a decrease in flow with a reduction of its head and that at zero flow, when all valves are closed, it will provide half the head pressure it has at maximum flow.

So how do you set such a pump? The pump needs to be strong radiatorss to provide heat for the whole house, and therefore you should set it to reach maximum head when all valves are open.

Altech Radiators, Altech Radiators Suppliers and Manufacturers at

If you know your maximum design flow, you can pick that point out of the pump diagram. If not, you open all the thermostats in the house fully assuming hydraulic balancing has been doneand then increase the power setting slowly until you see that the head pressure is not increasing anymore.

What happens if your setting is off? On the low side, you may experience boiler cycling and insufficient heating. Whistling is surely inconvenient, but cycling means less efficiency — so, if you err, do it on the high side. Since a Delta-Pv pump reacts to changing hydraulics only, there are cases where it has its limitations. The most obvious one is during nighttime setback. Your boiler reduces the feed temperature according to its timer setting to let the house cool down at night.

  BRAINPORT DEVICE PDF

All thermostatic valves react immediately and open fully, since they sense radiatoors the rooms are too cold. And the pump revs up to its maximum setting despite the fact that there is really no need for all that flow.

Several manufacturers have added nighttime setback detection by monitoring the water temperature flowing through the pump. They let the pump go to minimum speed whenever the temperature of the heating water drops quickly, and the pump comes radiattors to normal when the water temperature increases quickly.

The problem raviators that the pump does not know the outside temperature, and while the minimum pump performance may be sufficient most of the time, there can be very cold nights where the radiator furthest from the boiler may not get enough flow and may radiatods up. For that reason, the nighttime setback feature can be disabled.

Constant pressure control is ideal for systems in which the distribution pipe is non-existent or very short. A prime example is underfloor heating. The distribution altecg consists in most cases of an extremely short pipe run and the manifold. In such cases, system resistance is negligible. Therefore, the pump should supply the individual loops of the underfloor heating system with the same head pressure regardless of how many rooms are being heated. The setting of such a pump is comparatively easy.

The underfloor heating manufacturer will have specified the correct differential pressure for the individual loops, and the pump just needs to be set to this value.

If necessary, adjustments can be made to counter noise or insufficient heating. A high efficiency pump in a single family house will consume in the order of 50 to kWh of altceh a year. To heat the house, typically more than times that energy is required.

Even if radixtors account for the fact that electrical energy is more precious than heat, it should be clear that the overriding concern should always be to maximize the efficiency of the total system.

If you can lower the maximum feed temperature a bit by decreasing the delta-t in the loop through a higher pump setting, the heating energy saved in most cases will greatly exceed the additional pump consumption. A word of caution: While homeowners usually complain once a year about their gas bill, modern pumps with their nice displays and buttons make it very tempting for them to start saving in the wrong place. If you have adjusted their radiatprs system correctly, it may be a good idea to put a sticker on the pump showing the correct settings.

  COMPRESSEUR VIS BITZER PDF

Finally, you should consider the limits raidators autonomous pump control.

Pumps nowadays have intelligence built into them but they are seriously lacking in sensory input. They can detect the system rradiators and, if they have a built-in temperature sensor, they can detect system temperature.

On the other hand, radiztors heat source alhech comparatively a wealth of input, ranging from outside temperature information to that little button on your home heating control that informs it that you are having a party and that therefore you do not want the house to cool down at 10 p. The additional information makes it much easier for the control of your aotech or heat pump to optimize overall system efficiency.

In a time where even our refrigerators are getting a web connection, you can expect that before too long even standalone pumps will have a wireless connection to their boilers and will follow higher orders.

News and Events Careers Xylem Inc. Request Info Sales and service network. Home White Papers How to choose the correct speed control Why are high efficiency pumps speed controlled?

ALTECH Radiator 600 X 700mm White Type 11 Steel Single

Fixed speed control Setting the pump to one single pump curve is the only option in systems with constant hydraulics. Radiator heating loop This is the most common hydronic heating system.

Limits of proportional pressure control Since a Delta-Pv pump reacts to changing hydraulics only, there are cases where it has its limitations. Constant pressure control Constant pressure control is ideal for systems in which the distribution pipe is non-existent or very short. System efficiency versus pump efficiency A raditors efficiency pump in a single family house will consume alech the order of 50 to kWh of energy a year.

Outlook Finally, you should consider the limits of autonomous pump control.

Radiators | Jewson

Subscribe to be notified when new content is published Subscribe. Xylem presents new packaging design on wholesaler shelves in EMEA. How to choose the correct speed control for heating systems. Connect with us Sales and service Contact Us.

Convectors type 33, floor mounted

Copyright Xylem Inc. Xylem uses ‘cookies’ and ‘media beacons’. For more information, visit our Privacy Policy page.