Menu

3G3JX MANUAL PDF

0 Comments

The 3G3JX Inverter meets the EC Directives and UL/cUL standard frequency limit, Frequency jump, Curve acceleration/deceleration, Manual torque boost. The [email protected]@@ terminal symbols are shown in brackets. γΈ¨2. Connect a For detail of Inverter selection, refer to the JX series User’s Manual. ( TYPE [email protected] Model X Series Inverter. Thank you for purchasing JX inverter. To ensure safe operation, please be sure to read the safety precautions .

Author: Nakazahn Tehn
Country: Mauritania
Language: English (Spanish)
Genre: Education
Published (Last): 4 July 2010
Pages: 33
PDF File Size: 20.9 Mb
ePub File Size: 14.68 Mb
ISBN: 131-1-16482-454-6
Downloads: 98085
Price: Free* [*Free Regsitration Required]
Uploader: Brakasa

Enabled in constant speed operation selection 1. Wiring work must be carried out only by qualified personnel.

You cannot set analog inputs FV and FI to both target and feedback values simultaneously. Got it, continue to print.

Overview Chapter 1 Overview Describes features and names of parts. Maunal multi-step speed setting binary 3 C Kyoto, Japan Tel: Do not share the grounding electrode with other strong electrical devices. Disabled Free-run stop Otherwise, the motor may burn out. To use this function, set the DC injection braking selection A to The default setting is sink logic.

No limit selection For details on the operation and settings, refer to “Jogging Operation” manua Table of Contents Add to my manuals Add. To connect the ModBus, connect each Inverter in parallel as below.

That will change the function allocation on the control terminal block automatically. Example Multi-function input terminals S4, S2: Enables the parameter for the special 2nd motor.

  BROTZMAN RIABILITAZIONE ORTOPEDIA PDF

Press the Enter key to store the data. Data is out of the Inverter’s range for writing into the holding register. Safety Precautions Indications and Meanings of Safety Information In this user’s manual, the following precautions and signal words are used to provide information to ensure the safe use of the 3G3JX Inverter.

CF3 multi-step speed setting binary 3. Page 64 Operation Procedure Example: With this function, output voltage to the motor is based on that set in maunal AVR voltage selection.

OMRON 3G3JX USER MANUAL Pdf Download.

If the cable length is increased, the stray capacitance between the Inverter outputs and the ground is increased proportionally. Page Special Display List Display on Maunal Name Description Operator Shuts off the output if a ground fault between the Inverter output unit and the motor is detected when turning on the power.

Disabled b selection When forcibly stopping the load with an MC on the primary side of the main circuit, however, the regenerative braking does not work and the load coasts to a stop free run.

Normal operation A selection Page 33 Wiring Note 2: FA1 constant speed arrival signal Multi-function Loosen the front cover mounting screw. CF1 multi-step speed setting binary 1 Page Inverter is shortened. Doing so may result in a serious injury due mahual an electric shock. Page 94 Function Mode 3g3ix No. The code of the monitor mode is displayed as “d”. After completing the installation process, be sure to remove the covers from the Inverter before operation.

  ALESSANDRO BARICCO SETA LIBRO PDF

Omron 3G3JX User Manual Page 197

manul The monitor LED indicator “Hz” lights up while d is displayed. Data other than b and specified frequency parameters cannot be manul when the SFT terminal is ON. RV reverse C input 1 selection Page Function Manul Function code Maximum number of data Maximum data number in 1 Function code Function bytes in 1 message message Coil status reading 32 coils in bits Holding register content reading 4 registers in bytes Writing into the coil 1 coil in bits Writing into holding register 1 registers in bytes Page Function Mode Message configuration: Function name Data Default setting Unit Multi-function input 1 Page 63 Operation Procedure Example: Stops with auto recovery contacts.

Factor code h Trip monitor 3: Understanding the following configuration ensures more effective use of the product.

Omron 3G3JX User Manual (Page of )

A upper limit frequency Frequency lower 0. Page of Go. Do not connect the signal lines for inputs FV and FI simultaneously. Function name Data Default setting Unit 0.

The coil status change is shown in the following table. CF2 multi-step speed setting binary 2 C 1 selection A FI end ratio 0. FA2 over set frequency arrival signal C output terminal P1