Menu

2P102 DATASHEET PDF

0 Comments

datasheet pdf data sheet FREE from Datasheet (data sheet) FD F DFS2P FS2P S2P 2P P 02 2 FDFS2P 2P datasheet, 2P datasheets and manuals electornic semiconductor part. P, FDFS2P, MMDFS2P, FDFS2PA and other pdf’s. This device is designed specifically as a single package solution for DC to DC converters. It features a fast switching, low gate charge MOSFET with very low on -.

Author: Tygomi Badal
Country: Antigua & Barbuda
Language: English (Spanish)
Genre: Health and Food
Published (Last): 20 March 2005
Pages: 400
PDF File Size: 19.59 Mb
ePub File Size: 4.19 Mb
ISBN: 774-2-80003-369-2
Downloads: 89598
Price: Free* [*Free Regsitration Required]
Uploader: Vudoramar

The sensor can be a photoresistora photodiodea phototransistora silicon-controlled rectifier SCR or a triac. For the optical component, see optical isolator. The proposed configuration consist of two different parts. The sensors, be it photoresistors, photodiodes or phototransistors, cannot emit light.

The fastest opto-isolators employ PIN diodes in photoconductive mode. To reach the required threshold, solid-state relays contain stacks of up to thirty photodiodes wired in series.

Transformers and opto-isolators are the only two classes of electronic devices that offer reinforced protection — they protect both the equipment and the human user operating this equipment. Some optocouplers have a reflective pair configuration.

Commons category link is locally defined Wikipedia articles with GND identifiers. A special class of analog opto-isolators introduced by Burr-Brown uses two photodiodes and an input-side operational amplifier to compensate for diode non-linearity.

The gate of a MOSFET requires relatively small total charge to turn on and its leakage current in steady state is very low. Electronic equipment and signal and power transmission lines can be subjected to voltage surges induced by lightningelectrostatic dischargeradio frequency transmissionsswitching pulses spikes and perturbations in power supply.

An unrelated company, Silonex a division of Carlyle Group brands its photoresistive opto-isolators Audiohm Optocouplers. The response times of PIN diodes lie in the subnanosecond range; overall system speed is limited by delays in LED output and in biasing circuitry.

  ALTERNATIVE TO CFDOCUMENT PDF

The simplest bidirectional opto-isolator is merely a pair of LEDs placed face to face and held together with heat-shrink tubing.

The diode itself does not generate energy; it modulates the flow datssheet energy from an external source. When the darasheet is reverse-biased with an external voltage source, incoming light increases the reverse current flowing through the diode.

Usually opto-isolators transfer digital on-off signals, but some techniques allow them to be used with analog signals. Opto-isolators using field-effect transistors FETs as sensors are rare and, like vactrols, can be used as remote-controlled analog potentiometers provided that the voltage across the FET’s output terminal does not exceed a few hundred mV.

See also full specifications of currently produced devices: Opto-isolators rated for 2. Commercialization of LED technology in — caused a boom in optoelectronicsand by the end of the s the industry developed all principal types of opto-isolators.

Such fluctuations take hours to settle and can be only partially offset with feedback in the control circuit.

2P102A Datasheet PDF

The trademark has since been genericized[note 8] but the original Vactrols are still being manufactured by PerkinElmer. Si LEDs are the preferred choice for bidirectional devices.

A photodiode in photovoltaic mode can generate turn-on charge in a reasonably short time but its output voltage is many times less than the MOSFET’s threshold voltage.

The dome acts as a reflectorretaining all stray light and reflecting it onto the surface of the sensor, minimizing losses in a relatively long optical channel. Each coil can act as a primarypumping energy into a common magnetic coreor as a secondary — picking up energy stored in the core. Usually, optocouplers have a closed pair 2;102.

An opto-isolator connects input and output sides with a beam of light modulated by input current. This mode of operation is datasheer photoconductive mode.

This configuration refers to optocouplers with an open slot between the source and sensor that has the ability to influence incoming signals. The earliest opto-isolators, originally marketed as light cellsemerged in the s. The rate of charge is proportional to the intensity of incoming light. Views Read Edit View history.

  HONDA ST1100 BROCHURE PDF

Retrieved November 2, An opto-isolator contains a source emitter of light, almost always a near infrared light-emitting diode LEDthat converts electrical input signal into light, a closed optical channel also called dielectrical channel [7]and a photosensorwhich detects incoming light and either generates electric energy directly, ratasheet modulates 21p02 current flowing from an external power supply. Phototransistors are inherently slower than photodiodes.

They are the slowest, but also the most linear isolators and still retain a niche market in the audio and music 2p012. Because LEDs can sense light in addition to emitting it, construction of symmetrical, bidirectional opto-isolators is possible.

By using this site, you agree to the Terms of Use and Privacy Policy. A common type of opto-isolator consists of an LED and a phototransistor in the same opaque package. Alternatively, in the absence of external bias the diode converts the energy of light into electric energy by charging its terminals to a voltage of up to 0.

Opto-isolator – Wikipedia

The reflective pair configuration is suitable for the development of tachometers, movement detectors and reflectance monitors. Real-world LEDs and sensors are much smaller; see the photograph in Avago, p.

Retrieved November 5, All opto-isolators described so far are uni-directional.

Low to high [note 7]. Design with transistor opto-isolators requires generous allowances for wide fluctuations of parameters found in commercially available devices. American guitar and organ manufacturers of the s embraced the resistive opto-isolator as a convenient and cheap tremolo modulator. The majority of opto-isolators on the market use bipolar silicon phototransistor sensors.

A novel idea of a particular optical analog signal isolator was submitted on 3, June